- [Show page]
- [Old revisions]
- [[unknown link type]]
- []
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
linux:ilo [2014/09/10 16:00] kotrlik created |
linux:ilo [2015/11/11 09:40] (current) vondra [Setup network] |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| Pro ssh pristup je nutne pouzit parametry: | Pro ssh pristup je nutne pouzit parametry: | ||
| ssh -o ForwardAgent=no -o ForwardX11=no -o HostKeyAlgorithms=ssh-rsa,ssh-dss user@ip | ssh -o ForwardAgent=no -o ForwardX11=no -o HostKeyAlgorithms=ssh-rsa,ssh-dss user@ip | ||
| + | | ||
| + | Pro novejsi OpenSSH je treba pouzit nasledujici alias: | ||
| + | <code> | ||
| + | alias ilossh='ssh -o PasswordAuthentication=yes \ | ||
| + | -o ChallengeResponseAuthentication=no \ | ||
| + | -o GSSAPIAuthentication=no \ | ||
| + | -o HostbasedAuthentication=no \ | ||
| + | -o PubkeyAuthentication=no \ | ||
| + | -o RSAAuthentication=no \ | ||
| + | -o Compression=no \ | ||
| + | -o ForwardAgent=no \ | ||
| + | -o ForwardX11=no \ | ||
| + | -o KexAlgorithms=diffie-hellman-group1-sha1 \ | ||
| + | -o MACs=hmac-md5,hmac-sha1 \ | ||
| + | -o Ciphers=aes128-cbc,3des-cbc \ | ||
| + | -o HostKeyAlgorithms=ssh-rsa,ssh-dss' | ||
| + | |||
| + | </code> | ||
| + | |||
| + | ===== Setup LO100 ===== | ||
| + | LO100 is poor man's iLo that can be found in HP DL1xx - it is derived from IBM BCM | ||
| + | |||
| + | following commands should work on all machines equipped either with LO100 or iLO 3 and higher (maybe other management consoles - e.g. Dell, IBM, Sun) | ||
| + | ==== Install ipmitool ==== | ||
| + | the ipmitool utility allows you to change iLo settings without rebooting the server | ||
| + | - install the package<code bash> | ||
| + | apt-get install ipmitool | ||
| + | </code> | ||
| + | - the service job usually fails to run so you have to load following kernel modules in order to use ipmitool<code bash> | ||
| + | modprobe ipmi_msghandler | ||
| + | modprobe ipmi_devintf | ||
| + | modprobe ipmi_si</code> | ||
| + | - try to start the service again<code bash> | ||
| + | service ipmievd start</code> | ||
| + | |||
| + | ==== Setup users ==== | ||
| + | - list users:<code> | ||
| + | ipmitool user list | ||
| + | </code> | ||
| + | - change password for desired user - in this case user no 3<code> | ||
| + | ipmitool user set password 3 my-password | ||
| + | ipmitool user enable 3 | ||
| + | </code> | ||
| + | - set this user as administrator<code> | ||
| + | ipmitool user priv 3 4 | ||
| + | </code> | ||
| + | |||
| + | ==== Setup network ==== | ||
| + | - find out the lan channel<code bash> | ||
| + | for i in `seq 1 14`; do ipmitool lan print $i 2>/dev/null | grep -q ^Set && echo Channel $i; done</code>let the output be <code bash>Channel 2</code> | ||
| + | - show network configuration<code bash> | ||
| + | ipmitool lan print 2</code> | ||
| + | - setup static ip adress<code> | ||
| + | ipmitool lan set 2 ipsrc static | ||
| + | ipmitool lan set 2 ipaddr 10.0.255.x | ||
| + | ipmitool lan set 2 netmask 255.255.255.0 | ||
| + | ipmitool lan set 2 defgw ipaddr 10.0.255.1</code> | ||
| + | - do a cold reset<code bash> | ||
| + | ipmitool mc reset cold</code> if it doesn't take effect you can try connect to iLo via ssh and run<code>reset map1</code> | ||
linux/ilo.1410357614.txt.gz · Last modified: 2014/09/10 16:00 by kotrlik