- [Show page]
- [Old revisions]
- [[unknown link type]]
- []
Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
linux:ilo [2015/08/17 16:39] vondra |
linux:ilo [2015/11/11 09:40] (current) vondra [Setup network] |
||
---|---|---|---|
Line 17: | Line 17: | ||
-o MACs=hmac-md5,hmac-sha1 \ | -o MACs=hmac-md5,hmac-sha1 \ | ||
-o Ciphers=aes128-cbc,3des-cbc \ | -o Ciphers=aes128-cbc,3des-cbc \ | ||
- | -o HostKeyAlgorithms=ssh-rsa,ssh-dss ' | + | -o HostKeyAlgorithms=ssh-rsa,ssh-dss' |
</code> | </code> | ||
+ | |||
+ | ===== Setup LO100 ===== | ||
+ | LO100 is poor man's iLo that can be found in HP DL1xx - it is derived from IBM BCM | ||
+ | |||
+ | following commands should work on all machines equipped either with LO100 or iLO 3 and higher (maybe other management consoles - e.g. Dell, IBM, Sun) | ||
+ | ==== Install ipmitool ==== | ||
+ | the ipmitool utility allows you to change iLo settings without rebooting the server | ||
+ | - install the package<code bash> | ||
+ | apt-get install ipmitool | ||
+ | </code> | ||
+ | - the service job usually fails to run so you have to load following kernel modules in order to use ipmitool<code bash> | ||
+ | modprobe ipmi_msghandler | ||
+ | modprobe ipmi_devintf | ||
+ | modprobe ipmi_si</code> | ||
+ | - try to start the service again<code bash> | ||
+ | service ipmievd start</code> | ||
+ | |||
+ | ==== Setup users ==== | ||
+ | - list users:<code> | ||
+ | ipmitool user list | ||
+ | </code> | ||
+ | - change password for desired user - in this case user no 3<code> | ||
+ | ipmitool user set password 3 my-password | ||
+ | ipmitool user enable 3 | ||
+ | </code> | ||
+ | - set this user as administrator<code> | ||
+ | ipmitool user priv 3 4 | ||
+ | </code> | ||
+ | |||
+ | ==== Setup network ==== | ||
+ | - find out the lan channel<code bash> | ||
+ | for i in `seq 1 14`; do ipmitool lan print $i 2>/dev/null | grep -q ^Set && echo Channel $i; done</code>let the output be <code bash>Channel 2</code> | ||
+ | - show network configuration<code bash> | ||
+ | ipmitool lan print 2</code> | ||
+ | - setup static ip adress<code> | ||
+ | ipmitool lan set 2 ipsrc static | ||
+ | ipmitool lan set 2 ipaddr 10.0.255.x | ||
+ | ipmitool lan set 2 netmask 255.255.255.0 | ||
+ | ipmitool lan set 2 defgw ipaddr 10.0.255.1</code> | ||
+ | - do a cold reset<code bash> | ||
+ | ipmitool mc reset cold</code> if it doesn't take effect you can try connect to iLo via ssh and run<code>reset map1</code> |
linux/ilo.1439822358.txt.gz · Last modified: 2015/08/17 16:39 by vondra